83Plus:Ports:09: Difference between revisions

From WikiTI
Jump to navigationJump to search
mNo edit summary
 
Added information on what writing does.
 
(5 intermediate revisions by 3 users not shown)
Line 1: Line 1:
'''Note:''' Do not take the information on this template page as actual documentation!
[[Category:83Plus:Ports:By_Address|09 - Link Assist Status/CPU Speed 0 Signaling Rate]] [[Category:83Plus:Ports:By_Name|Link Assist Status/CPU Speed 0 Signaling Rate]]
 
The Ports are named by their number, in hexadecimal. An example is [[83Plus:Ports:00]].
 
You also must put a variation on the following code into your page to have it categorized:
NaodW29-nowiki524ead3d48187e5400000001
 
----
 
== Synopsis ==
== Synopsis ==
'''Port Number:''' 06h
'''Port Number:''' 09h


'''Function:''' Flash Memory Paging
'''Function:''' Link Assist Status/CPU Speed 0 Signaling Rate


This port controls what page is swapped into the 4000h to 7FFFh range. ('''DO NOT''' take this template page as real documentation on port 6!)
This port gives information on the status of the hardware link assist.


=== Read Values ===
=== Read Values ===
* [00h - FFh]: The current port mapped to the memory range 4000h through 7FFFh.
* Bit 0: Set if an interrupt was generated by receiving a byte.
* Bit 1: Set if an interrupt was generated when a byte can be sent.
* Bit 2: Set if an interrupt was generated due to an error in transmission.
* Bit 3: Set if the assist is currently receiving data
* Bit 4: Set if the assist has read a complete byte (which can be read from [[83Plus:Ports:0A|port 0A]])
* Bit 5: Set if the assist is ready to write data (via [[83Plus:Ports:0D|port 0D]])
* Bit 6: Set if there was an error during transmission
* Bit 7: Set if the link assist is currently sending a byte.


=== Write Values ===
=== Write Values ===
* [00h - FFh]: The new page to swap in to the memory range 4000h through 7FFFh
Writing to this port sets the signaling rate of the link assist in CPU speed mode 0 (6 MHz); the link assist uses the same clock as the CPU. Bits 5 through 7 control a divisor to the clock before it reaches the link assist, affecting how fast the link assist can detect changes in the signal states. It will divide by 2^n, allowing you to divide by 1, 2, 4 ... 64. Value 111b (7) will halt the link assist. Bits 0 through 4 control how much time to wait between bits. TI desires a minimum time between bits of 2 microseconds.
 
''Note: if you would have bitwise flags for your port, label them "bit X".''


== Comments ==
== Comments ==
The behavior of this port changes in different memory map modes.
This port only exists on the 83+ SE and the 84+.
 
== Example ==
NaodW29-nowiki524ead3d48187e5400000002


== Credits and Contributions ==
== Credits and Contributions ==
* '''/dev/urandom:''' Because of your randomness, this project is possible.
* '''Michael Vincent:''' Original documentation of the link assist

Latest revision as of 03:41, 12 August 2013

Synopsis

Port Number: 09h

Function: Link Assist Status/CPU Speed 0 Signaling Rate

This port gives information on the status of the hardware link assist.

Read Values

  • Bit 0: Set if an interrupt was generated by receiving a byte.
  • Bit 1: Set if an interrupt was generated when a byte can be sent.
  • Bit 2: Set if an interrupt was generated due to an error in transmission.
  • Bit 3: Set if the assist is currently receiving data
  • Bit 4: Set if the assist has read a complete byte (which can be read from port 0A)
  • Bit 5: Set if the assist is ready to write data (via port 0D)
  • Bit 6: Set if there was an error during transmission
  • Bit 7: Set if the link assist is currently sending a byte.

Write Values

Writing to this port sets the signaling rate of the link assist in CPU speed mode 0 (6 MHz); the link assist uses the same clock as the CPU. Bits 5 through 7 control a divisor to the clock before it reaches the link assist, affecting how fast the link assist can detect changes in the signal states. It will divide by 2^n, allowing you to divide by 1, 2, 4 ... 64. Value 111b (7) will halt the link assist. Bits 0 through 4 control how much time to wait between bits. TI desires a minimum time between bits of 2 microseconds.

Comments

This port only exists on the 83+ SE and the 84+.

Credits and Contributions

  • Michael Vincent: Original documentation of the link assist