Difference between revisions of "83Plus:Ports:4A"
From WikiTI
Thepenguin77 (Talk | contribs) |
Thepenguin77 (Talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | [[Category:83Plus:Ports:By Address|4A - | + | [[Category:83Plus:Ports:By Address|4A - USB Line Control]] [[Category:83Plus:Ports:By Name|USB Line Control]] |
{{84P-Only Port|0A}} | {{84P-Only Port|0A}} | ||
== Synopsis == | == Synopsis == | ||
'''Port Number:''' 4A | '''Port Number:''' 4A | ||
| − | '''Function:''' | + | '''Function:''' USB Line Control |
| − | Using this port, you can control the D+ | + | Using this port, you can control the D+ from an A-type connector and the D− line from a B-type connector. |
=== Read Values === | === Read Values === | ||
| Line 12: | Line 12: | ||
* Bit 1: Set if not connected to computer. Flashes when talking to computer. | * Bit 1: Set if not connected to computer. Flashes when talking to computer. | ||
* Bit 2: Set if not connected to computer. | * Bit 2: Set if not connected to computer. | ||
| − | * Bit 3: If set, | + | * Bit 3: If set, the corresponding line is forced high. Max 0.79 mA. |
| − | * Bit 4: Only significant if bit 3 is set. If this is set, | + | * Bit 4: Only significant if bit 3 is set. If this is set, the corresponding line gets extra power. Max total 1.52 mA. |
| − | * Bit 5: Reset means | + | * Bit 5: Reset means the corresponding line is getting 0.05 V at 15μA. |
* Bit 6: Always 0 | * Bit 6: Always 0 | ||
* Bit 7: Always 0 | * Bit 7: Always 0 | ||
| Line 20: | Line 20: | ||
=== Write Values === | === Write Values === | ||
* Bits 0-2: No effect | * Bits 0-2: No effect | ||
| − | * Bit 3: Set to force | + | * Bit 3: Set to force the corresponding line. Max output: 0.79 mA. |
| − | * Bit 4: If bit 3 is set. Setting this give | + | * Bit 4: If bit 3 is set. Setting this give the corresponding line extra power. Max total output 1.52 mA. |
| − | * Bit 5: Resetting this gives | + | * Bit 5: Resetting this gives the corresponding line 0.05 V at 15μA. |
* Bits 6-7: No effect | * Bits 6-7: No effect | ||
== Comments == | == Comments == | ||
| − | If you don't like USB protocol, you could try to use this port for communication, or | + | If you don't like USB protocol, you could try to use this port for communication, or maybe as a "ready" signal. Anyways, when you are done, output 20h. |
Revision as of 15:00, 3 June 2011
| This port only exists on the the TI-84 Plus and the TI-84 Plus Silver Edition. On the standard TI-83 Plus, it acts as a shadow of port 0A. On the TI-83 Plus Silver Edition, this port has no effect. |
Synopsis
Port Number: 4A
Function: USB Line Control
Using this port, you can control the D+ from an A-type connector and the D− line from a B-type connector.
Read Values
- Bit 0: Set if connected to computer.
- Bit 1: Set if not connected to computer. Flashes when talking to computer.
- Bit 2: Set if not connected to computer.
- Bit 3: If set, the corresponding line is forced high. Max 0.79 mA.
- Bit 4: Only significant if bit 3 is set. If this is set, the corresponding line gets extra power. Max total 1.52 mA.
- Bit 5: Reset means the corresponding line is getting 0.05 V at 15μA.
- Bit 6: Always 0
- Bit 7: Always 0
Write Values
- Bits 0-2: No effect
- Bit 3: Set to force the corresponding line. Max output: 0.79 mA.
- Bit 4: If bit 3 is set. Setting this give the corresponding line extra power. Max total output 1.52 mA.
- Bit 5: Resetting this gives the corresponding line 0.05 V at 15μA.
- Bits 6-7: No effect
Comments
If you don't like USB protocol, you could try to use this port for communication, or maybe as a "ready" signal. Anyways, when you are done, output 20h.
