Difference between revisions of "83Plus:Ports:07"
From WikiTI
m (→Example: used the stack to store the old page) |
m |
||
| (6 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| + | [[Category:83Plus:Ports:By_Address|07 - Memory Page B]] [[Category:83Plus:Ports:By_Name|Memory Page B]] | ||
== Synopsis == | == Synopsis == | ||
'''Port Number:''' 07h | '''Port Number:''' 07h | ||
| Line 4: | Line 5: | ||
'''Function:''' Flash/RAM Memory Paging (Bank B) | '''Function:''' Flash/RAM Memory Paging (Bank B) | ||
| − | This port controls what page is swapped into Memory Bank B (see comments). | + | This port controls what page is swapped into Memory Bank B (see comments). On the TI-84+CSE, port [[83Plus:Ports:0F|0F]] also affects MemB. |
| + | |||
| + | See also [[83Plus:Memory Mapping|Memory Mapping]]. | ||
=== Read Values === | === Read Values === | ||
| − | * The current port mapped to Memory Bank B | + | * The current port mapped to Memory Bank B. |
** 83+ Basic: If a RAM page is swapped in, the port reads the RAM page number with bit 6 set. If a ROM page is swapped in, the port reads the ROM page number with bit 6 reset. | ** 83+ Basic: If a RAM page is swapped in, the port reads the RAM page number with bit 6 set. If a ROM page is swapped in, the port reads the ROM page number with bit 6 reset. | ||
** 83+ Silver, any 84+: If a RAM page is swapped in, the port reads the RAM page number with bit 7 set. If a ROM page is swapped in, the port reads the ROM page number with bit 7 reset. | ** 83+ Silver, any 84+: If a RAM page is swapped in, the port reads the RAM page number with bit 7 set. If a ROM page is swapped in, the port reads the ROM page number with bit 7 reset. | ||
=== Write Values === | === Write Values === | ||
| − | * The page number to swap into Memory Bank B | + | * The page number to swap into Memory Bank B. |
** 83+ Basic: If bit 6 is set, bit 0 will choose between the two RAM pages (40h or 41h). If bit 6 is 0, bits 0~4 select a page from ROM (00h through 1Fh). | ** 83+ Basic: If bit 6 is set, bit 0 will choose between the two RAM pages (40h or 41h). If bit 6 is 0, bits 0~4 select a page from ROM (00h through 1Fh). | ||
** 83+ SE, 84+ (any): If bit 7 is set, bits 0~2 will choose any of the 8 RAM pages (80h through 87h). If bit 7 is 0, bits 0~5 on the 84+ Basic, or bits 0~6 on either SE will select a page from ROM (00h through 3Fh or 7Fh). | ** 83+ SE, 84+ (any): If bit 7 is set, bits 0~2 will choose any of the 8 RAM pages (80h through 87h). If bit 7 is 0, bits 0~5 on the 84+ Basic, or bits 0~6 on either SE will select a page from ROM (00h through 3Fh or 7Fh). | ||
== Comments == | == Comments == | ||
| − | The behavior of this port changes in different memory map modes. See [[83Plus:Ports:04|Port 04h]] for details about memory map modes. | + | Under normal circumstanes this port controls the page mapped to 8000h. The behavior of this port changes in different memory map modes. See [[83Plus:Ports:04|Port 04h]] for details about memory map modes. |
| − | Unless you're really clever, the calculator will crash if you return to TIOS with anything other than RAM Page 1 (41h on 83+ Basic, 81h on everything else) swapped in. | + | Unless you're really clever, the calculator will crash if you return to TIOS, call most system routines, or even allow an interrupt to occur with anything other than RAM Page 1 (41h on 83+ Basic, 81h on everything else) swapped in. |
== Example == | == Example == | ||
| − | <nowiki>push af | + | <nowiki> di |
| − | in a,(7) | + | push af |
| − | push af | + | in a,(7) |
| − | ld a,1 | + | push af |
| − | out (7),a | + | ld a,1 |
| − | ; do stuff that needs page 1 swapped in | + | out (7),a |
| − | pop af | + | ; do stuff that needs page 1 swapped in |
| − | out (7),a | + | pop af |
| − | pop af</nowiki> | + | out (7),a |
| + | pop af | ||
| + | ei</nowiki> | ||
Latest revision as of 20:31, 19 February 2013
Synopsis
Port Number: 07h
Function: Flash/RAM Memory Paging (Bank B)
This port controls what page is swapped into Memory Bank B (see comments). On the TI-84+CSE, port 0F also affects MemB.
See also Memory Mapping.
Read Values
- The current port mapped to Memory Bank B.
- 83+ Basic: If a RAM page is swapped in, the port reads the RAM page number with bit 6 set. If a ROM page is swapped in, the port reads the ROM page number with bit 6 reset.
- 83+ Silver, any 84+: If a RAM page is swapped in, the port reads the RAM page number with bit 7 set. If a ROM page is swapped in, the port reads the ROM page number with bit 7 reset.
Write Values
- The page number to swap into Memory Bank B.
- 83+ Basic: If bit 6 is set, bit 0 will choose between the two RAM pages (40h or 41h). If bit 6 is 0, bits 0~4 select a page from ROM (00h through 1Fh).
- 83+ SE, 84+ (any): If bit 7 is set, bits 0~2 will choose any of the 8 RAM pages (80h through 87h). If bit 7 is 0, bits 0~5 on the 84+ Basic, or bits 0~6 on either SE will select a page from ROM (00h through 3Fh or 7Fh).
Comments
Under normal circumstanes this port controls the page mapped to 8000h. The behavior of this port changes in different memory map modes. See Port 04h for details about memory map modes.
Unless you're really clever, the calculator will crash if you return to TIOS, call most system routines, or even allow an interrupt to occur with anything other than RAM Page 1 (41h on 83+ Basic, 81h on everything else) swapped in.
Example
di push af in a,(7) push af ld a,1 out (7),a ; do stuff that needs page 1 swapped in pop af out (7),a pop af ei
