84PCE:Ports:A000: Difference between revisions

From WikiTI
Jump to navigationJump to search
No edit summary
Line 8: Line 8:
'''Function:''' Set the mode of the keypad controller
'''Function:''' Set the mode of the keypad controller


F50000 (R/W):
*F50000 (R/W):


Bits 0-1: Scan mode
**Bits 0-1: Scan mode


*Mode 0: Idle.
***Mode 0: Idle.


*Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).
***Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).


*Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.
***Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.


*Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.
***Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.


Bits 2-15: Number of APB cycles to wait before scanning each row
**Bits 2-15: Number of APB cycles to wait before scanning each row


Bits 16-31: Number of APB cycles to wait between scans
**Bits 16-31: Number of APB cycles to wait between scans


F50004 (R/W):
*F50004 (R/W):
Bits 0-7: Number of rows to read (later rows are not updated in F50010-F5002F, and just read as whatever they were before being disabled)
**Bits 0-7: Number of rows to read (later rows are not updated in F50010-F5002F, and just read as whatever they were before being disabled)


Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)
**Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)


F50008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.
*F50008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.


*Bit 0: Keypad scan complete
**Bit 0: Keypad scan complete


*Bit 1: Keypad data register changed
**Bit 1: Keypad data register changed


*Bit 2: Key pressed in mode 1
**Bit 2: Key pressed in mode 1


F5000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [F50008] should cause an interrupt.
*F5000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [F50008] should cause an interrupt.


F50010-F5002F (R): Keypad data, one halfword per row.
*F50010-F5002F (R): Keypad data, one halfword per row.


F50030-F5003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.
*F50030-F5003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.

Revision as of 09:35, 31 March 2015

Synopsis

Port Number: A000-?

Memory-mapped address: F50000-?

Function: Set the mode of the keypad controller

  • F50000 (R/W):
    • Bits 0-1: Scan mode
      • Mode 0: Idle.
      • Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).
      • Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.
      • Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.
    • Bits 2-15: Number of APB cycles to wait before scanning each row
    • Bits 16-31: Number of APB cycles to wait between scans
  • F50004 (R/W):
    • Bits 0-7: Number of rows to read (later rows are not updated in F50010-F5002F, and just read as whatever they were before being disabled)
    • Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)
  • F50008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.
    • Bit 0: Keypad scan complete
    • Bit 1: Keypad data register changed
    • Bit 2: Key pressed in mode 1
  • F5000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [F50008] should cause an interrupt.
  • F50010-F5002F (R): Keypad data, one halfword per row.
  • F50030-F5003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.