84PCE:Ports:A000: Difference between revisions

From WikiTI
Jump to navigationJump to search
Line 8: Line 8:
'''Function:''' Set the mode of the keypad controller
'''Function:''' Set the mode of the keypad controller


*F50000 (R/W):
The CE appears to use the same keypad controller as the nSpire.


**Bits 0-1: Scan mode
* F50000 (R/W):
** Bits 0-1: Scan mode
*** Mode 0: Idle.
*** Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).
*** Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.
*** Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.
** Bits 2-15: Number of APB cycles to wait before scanning each row
** Bits 16-31: Number of APB cycles to wait between scans


***Mode 0: Idle.
* F50004 (R/W):
** Bits 0-7: Number of rows to read (later rows are not updated in F50010-F5002F, and just read as whatever they were before being disabled)
** Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)
* F50008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.
** Bit 0: Keypad scan complete
** Bit 1: Keypad data register changed
** Bit 2: Key pressed in mode 1


***Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).
* F5000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [F50008] should cause an interrupt.


***Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.
* F50010-F5002F (R): Keypad data, one halfword per row.


***Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.
* F50030-F5003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.
 
**Bits 2-15: Number of APB cycles to wait before scanning each row
 
**Bits 16-31: Number of APB cycles to wait between scans
 
*F50004 (R/W):
**Bits 0-7: Number of rows to read (later rows are not updated in F50010-F5002F, and just read as whatever they were before being disabled)
 
**Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)
 
*F50008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.
 
**Bit 0: Keypad scan complete
 
**Bit 1: Keypad data register changed
 
**Bit 2: Key pressed in mode 1
 
*F5000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [F50008] should cause an interrupt.
 
*F50010-F5002F (R): Keypad data, one halfword per row.
 
*F50030-F5003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.

Revision as of 09:38, 31 March 2015

Synopsis

Port Number: A000-?

Memory-mapped address: F50000-?

Function: Set the mode of the keypad controller

The CE appears to use the same keypad controller as the nSpire.

  • F50000 (R/W):
    • Bits 0-1: Scan mode
      • Mode 0: Idle.
      • Mode 1: Indiscriminate key detection. Data registers are not updated, but whenever any key is pressed, interrupt bit 2 is set (and cannot be cleared until the key is released).
      • Mode 2: Single scan. The keypad is scanned once, and then the mode returns to 0.
      • Mode 3: Continuous scan. When scanning completes, it just starts over again after a delay.
    • Bits 2-15: Number of APB cycles to wait before scanning each row
    • Bits 16-31: Number of APB cycles to wait between scans
  • F50004 (R/W):
    • Bits 0-7: Number of rows to read (later rows are not updated in F50010-F5002F, and just read as whatever they were before being disabled)
    • Bits 8-15: Number of columns to read (later column bits in a row are set to 1 when it is updated)
  • F50008 (R/W): Keypad interrupt status/acknowledge (3-bit). Write "1" bits to acknowledge.
    • Bit 0: Keypad scan complete
    • Bit 1: Keypad data register changed
    • Bit 2: Key pressed in mode 1
  • F5000C (R/W): Keypad interrupt mask (3-bit). Set each bit to 1 if the corresponding event in [F50008] should cause an interrupt.
  • F50010-F5002F (R): Keypad data, one halfword per row.
  • F50030-F5003F (R/W): Keypad GPIOs. Each register is 20 bits, with one bit per GPIO. The role of each register is unknown.