Difference between revisions of "83Plus:Software:usb8x/Error Codes"
From WikiTI
(→Error Codes: 82 clarification) |
(No device clarification) |
||
| Line 28: | Line 28: | ||
|11 || EPGetDes || An unsupported descriptor was requested from [[../Asm_Interface/ReadDescriptor|ReadDescriptor]]. | |11 || EPGetDes || An unsupported descriptor was requested from [[../Asm_Interface/ReadDescriptor|ReadDescriptor]]. | ||
|- | |- | ||
| − | |12 || NoDevice || No Device is connected. | + | |12 || NoDevice || No Device is connected. You'll get this error if you plug in a mini B cable instead of mini A. |
|- | |- | ||
|13 || FindDescriptor || An error occured in [[../Asm_Interface/FindDescriptor|FindDescriptor]]. | |13 || FindDescriptor || An error occured in [[../Asm_Interface/FindDescriptor|FindDescriptor]]. | ||
Revision as of 18:03, 9 September 2006
Error codes may be returned via both the [[../Asm_Interface|assembly language interface]] and the [[../BASIC_Interface|BASIC interface]]. In the BASIC interface, the error code is returned in the first element of the return list. In the assembly language interface, an error is generally indicated by a return with the carry flag set. The error code can then be read via [[../Asm_Interface/GetErrorCode|GetErrorCode]]. Error code equates are located in usb8x.inc.
Error Codes
| Error # | Name | Info |
|---|---|---|
| 0 | OK | No error occured |
| 1 | Port82 | The previous command failed or did not terminate. This generally happens during initialization. |
| 2 | Port91Bit2 | An error condition was detected via port 91 (NAK?) |
| 3 | Port91Bit4 | An error condition was detected via port 91 (Stall?) |
| 4 | Port4C | Port 4C did not hold the expected value. This generally happens during initialization. |
| 5 | Port4D | Port 4D did not hold the expected value. This generally happens during initialization. |
| 6 | Port3A | Port 3A did not hold the expected value. This generally happens during initialization. |
| 7 | Port81 | Port 81 did not hold the expected value. This generally happens during initialization. |
| 8 | Port8C | The frame counter did not start. This often indicates low batteries. |
| 9 | Port8F | Port 8F did not hold the expected value. This generally happens during initialization. |
| 10 | EPIndex | A non existant entry point was called. Be sure to check for the minimum required version of usb8x before calling entry points. |
| 11 | EPGetDes | An unsupported descriptor was requested from [[../Asm_Interface/ReadDescriptor|ReadDescriptor]]. |
| 12 | NoDevice | No Device is connected. You'll get this error if you plug in a mini B cable instead of mini A. |
| 13 | FindDescriptor | An error occured in [[../Asm_Interface/FindDescriptor|FindDescriptor]]. |
| 14 | BadClass | The attached device does not have the required class. (i.e. a keyboard is connected when [[../Asm_Interface/MouseInit|MouseInit]] is called). |
| 15 | Timeout | A timeout occured while waiting for data. This currently is only returned by [[../BASIC_Interface/MouseDo|MouseDo]]. |
| 16 | BadID | The attached device does not have the required vendor or device ID. |
| 17 | ReadDescriptor | An error occured in [[../Asm_Interface/ReadDescriptor|ReadDescriptor]]. Check sub error code for additional information. |
| 18 | Init | An error occured during initialization. Check sub error code for more information. |
| 19 | AutoSetup | An error occured during [[../Asm_Interface/AutoSetup|AutoSetup]]. Check sub error code for more information. |
| 20 | Demo | An error occured in demo code. This should not be returned via either of the programming interfaces. |
| 21 | FindPipe | An error occured in [[../Asm_Interface/FindPipe|FindPipe]]. This error may occasionally improperly be listed a sub error code, because AutoSetup generates a FindPipe error during normal operation. |
| 22 | Stub | Returned by stub routines (not current used). |
| 23 | GetMaxPacketSize | An error occured while trying to determine the maximum supported packet size. |
| 24 | SetAddress | An error occured while trying to set the device address |
| 25 | SendCmd | There was a problem sending mass storage I/O commands |
| 26 | LargeSect | Bytes-per-sector is larger than 512 (not supported) |
| 27 | NoParts | There were no FAT16 partitions found on the connected mass storage device |
| 28 | NoMoreMemory | The previous function failed because there is no more free memory (this is a very bad thing) |
| 29 | InvalidPartition | The FAT16 partition found is invalid because it does not contain 0AA55h |
| 30 | NotFile | The path passed to a function is to a directory or volume label, not a file |
| 31 | NotValidPath | The path passed to a function is completely invalid |
| 32 | CorruptFile | A file is corrupted or otherwise not as expected |
| 33 | NotFound | File or directory was not found |
| 34 | DuplicateFound | Duplicate calculator variable was found and not overwritten |
| 35 | NotEnoughMem | There was not enough memory to create the new calculator variable |
| 36 | AlreadyExists | An 8x* file of the same name already exists in the current directory |
| 37 | StrNotFound | String variable from BASIC OpenLib/ExecLib function was not found |
| 38 | VarEmpty | Variable was empty and transfer was not completed (this is a bad thing; delete new, incomplete file) |
| 39 | NoParts32 | FAT32 partitions were found, but none were FAT16 (make sure you reformat your drive as FAT16) |
| 40 | NoData | There was no data to report. Returned by [[../BASIC_Interface/KBDGetKey|KBDGetKey]] |
| 41 | Version | A pre-2.30 version of TIOS is loaded on the calculator. |
Be aware that the error codes listed on this page are in decimal, while the error codes displayed in USBInfo are in hexadecimal.
