Difference between revisions of "83Plus:OS:Raw Flash Commands"

Revision as of 12:45, 17 February 2012

] The TI-83+ through TI-84+SE have a flash chip whose data can be erased and rewritten. Issuing write and erase commands is done through memory-mapped writes. The flash chip will not accept any commands unless flash is unlocked. Additionally, any read from flash while issuing a command sequence will abort the command sequence. Consequentially, command sequences can only be issued from RAM and interrupts must be disabled. (Or IM 2 with the ISR and IVT entirely in RAM, I suppose.)

Basic Flash Commands

It takes the flash chip a long time to perform a write or erase operation. During this time, it is impossible to read data from the flash chip, because all reads will simply report a status byte.

Reset

You can reset the flash chip by writing 0F0h to 0000h.

ld a, 0F0h
ld (0), a

Reset the flash chip if a program or erase operation fails, to abort either of those, and to leave autoselect mode. The flash chip does not accept resets during write or erase operations.

Writing

The design of flash memory is such that a 0 can be written over a 1, but the reverse is not possible. Any write attempting to do this will fail. To write a 1 over a 0, see the below.

writeFlashByte:
; Writes a byte to flash.  Flash must be unlocked.  Be aware that pressing CLEAR
; will abort the write.
; Inputs:
;  - B: Byte to write
;  - C: Page
;  - HL: Address to write to.  This will not be wrapped.
; Outputs:
;  - NZ on failure
; Kills:
;  - AF, BC
; Protips:
;  - Calling writeFlashByteRaw instead will skip the page changing
;  - Do push bc \ pop af afterwards to restore flags to pre-call values.  That's
;    right, documented side-effect programming! 
	in	a, (memPageAPort)	; save page
	push	af
	ld	a, c
	out	(6), a
	di
	call	writeFlashByteRaw
	ei
	pop	bc	; restore page without screwing up flags
	ld	a, b
	out	(memPageAPort), a
	ret
writeFlashByteRaw:
; Flash program sequence
	ld	a, 0AAh	; First bus cycle---unlock
	ld	(0AAAh), a
	ld	a, 55h	; Second bus cycle---unlock
	ld	(0555h), a
	ld	a, 0A0h	; Third bus cycle---write command
	ld	(0AAAh), a
	ld	(hl), b	; Fourth bus cycle---program data
; Wait for the write operation to complete
	ld	a, 0FDh		; This checks for the CLEAR key.
	out	(keyPort), a		; If pressed, it aborts.
	inc	hl
	dec	hl
programWaitLoop:
	in	a, (keyPort)
	cp	0BFh
	jr	z, abortProgram
	ld	a, b
	xor	(hl)
	bit	7, a
	jr	z, programDone
	bit	5, (hl)
	jr	z, programWaitLoop
abortProgram:
	ld	a, 0F0h
	ld	(0000h), a
	inc	a
programDone:
	ret

Erasing

The design of flash memory is such that writing a 1 over a 0 is not possible, except in large blocks known as sectors. The flash chips TI likes to use have sectors that are almost all 64 K in size, except the last which, which is broken up into several sectors. Erase operations take a long time, during which running code from flash is impossible. If you want, you could probably make something blink or something while you're waiting.

eraseSector:
; Erases a sector of flash. Note: Use eraseSectorRaw for the certificate.
; Inputs:
;  - C: Page
; Outputs:
;  - Z on fail (this is opposite of writeFlashByte)
; Kills:
;  - AF, BC, HL
	in	a, (memPageAPort)
	push	af
	ld	a, c
	out	(memPageAPort), a
	ld	hl, 4000h
	di
	call	eraseSectorRaw
	ei
	pop	bc
	ld	a, b
	out	(memPageAPort), a
	ret
eraseSectorRaw:
; Flash program sequence
	ld	a, 0AAh	; First bus cycle---unlock
	ld	(0AAAh), a
	ld	a, 55h	; Second bus cycle---unlock
	ld	(0555h), a
	ld	a, 080h	; Third bus cycle---write command
	ld	(0AAAh), a
	ld	a, 0AAh	; Fourth bus cycle---unlock (again)
	ld	(0AAAh), a
	ld	a, 55h	; Fifth bus cycle---unlock (again)
	ld	(0555h), a
	ld	a, 30h ; Do not change this value. In theory, you could superbrick your calculator.
	ld	(hl), a
; Wait for the erase operation to complete
	ld	a, 0FDh
	out	(keyPort), a
	inc	hl
	dec	hl        
eraseWaitLoop:
	in	a, (keyPort)
	cp	0BFh
	jr	z, abortErase
	ld	a, (hl)
	bit	7, a
	jr	nz, eraseDone
	bit	5, a
	jr	z, eraseWaitLoop
abortErase:
	ld	a, 0F0h
	ld	(4000h), a
	xor	a
eraseDone:
	ret

Erase Suspend

The flash chip supports suspending an erase operation in program. This allows you to read data from the flash chip again. I'm not sure why would want to do this, but

ld a, 0B0h
ld (0), a

will suspend an erase operation. Then

ld a, 30h
ld (0), a

will resume the erase operation. According to the data sheet, you can actually start writing data to another sector and resume the erase later.

Full Chip Erase

Do not use this command under any circumstances. It will fully brick your calculator by means of erasing the boot sector (and everything else).

Autoselect Mode

The flash chips support a set of commands known as the autoselect commands. These commands are intended to allow the flash chip to identify itself to a manufacturer and to verify that sectors are protected. However, they are also usable in-system. To use the autoselect commands, you must first unlock flash.

The basic code for an autoselect operation is

; First bus cycle---unlock
ld	a, 0AAh
ld	(0AAAh), a
; Second bus cycle---unlock
ld	a, 55h
ld	(0555h), a
; Third bus cycle---write command
ld	a, 090h
ld	(0AAAh), a
; Read autoselect code
ld	a, (address)
ld	b, a
ld	a, 0F0h ; You need to issue a reset command to exit autoselect mode
ld	(0000h), a

where address is the code for the autoselect command. Address 0 returns the Manufacturer ID; address 2 returns the device ID. Known manufacturer IDs are

Though the manufacturer ID changes from unit to unit, the device ID should be consistent:

Thus, a TI-83+SE and a TI-84+SE should both have C4 for the device ID; a TI-84+ should have DA for the device ID; and a TI-83+ should have 23 or B9 for the device.

If you swap the first page of any sector into the 4000h memory bank and read from 4004h, it will return whether or not that sector is protected by the flash chip's built-in write/erase lock. This always returns 0 on all TI-83+SE and TI-84+/SEs because TI has never used the locking feature in those units.

It appears that TI used to use the flash chip's locking feature on the original TI-83+, because older units read 01 for sector 1Fh. (Older units read 23 for the device ID, and newer units read B9 for the device ID. It is possible that the switch to the B9 devices occurred at the same time as the switch to the ASIC for the TI-83+.) However, since at least 2007, TI has not used the locking feature on the TI-83+. These units always read 0. Therefore, it is still possible that the ASIC supports unlocking the boot sector of these units.