Difference between revisions of "84PCE:Ports:D000"
From WikiTI
Calc84maniac (Talk | contribs) (Add closer matching datasheet for the LCD controller) |
Calc84maniac (Talk | contribs) (Add more descriptions to SPI controller registers) |
||
| Line 8: | Line 8: | ||
This appears to be an FTSSP010 or compatible SPI controller that interfaces with the LCD. The command set seems to closely match the Sitronix ST7789 family [https://www.rhydolabz.com/documents/33/ST7789.pdf]. | This appears to be an FTSSP010 or compatible SPI controller that interfaces with the LCD. The command set seems to closely match the Sitronix ST7789 family [https://www.rhydolabz.com/documents/33/ST7789.pdf]. | ||
| + | |||
| + | Note that the SPI controller may also be configured to interface with the ARM coprocessor on Python models, via some ports in the 00xx range. The state of this configuration should be considered unknown when starting a program in TI-OS. In order to reliably use the LCD interface, the _boot_InitializeHardware routine should be called at the start of a program to select the LCD interface and reset its configuration to the default. | ||
| Line 24: | Line 26: | ||
|0000182B | |0000182B | ||
|007FFFFF | |007FFFFF | ||
| − | |CR1: Boot code initializes to 02000B. Bits 0-15 are clock divider - 1, bits 16-23 are data length - 1, and bits 24-31 are padding length. | + | |CR1: Boot code initializes to 02000B. Bits 0-15 are clock divider - 1, bits 16-23 are data length - 1, and bits 24-31 are padding length.<br/>Base clock is likely 12 MHz (unconfirmed whether this changes with CPU speed).<br/>Sending with a clock divider of 1 seems to be within the LCD controller specs, but receiving may require a larger divider. |
|- | |- | ||
|D008<br/>F80008 | |D008<br/>F80008 | ||
|0002000B | |0002000B | ||
|00000F8F | |00000F8F | ||
| − | |CR2: Boot code initializes to 010C.<br/>Bit 0 is set to transfer data.<br/>Bit 7 is set | + | |CR2: Boot code initializes to 010C.<br/>Bit 0 is set to transfer data and activate the SPI chip select signal.<br/>Writing a 1 to Bit 2 clears the receive FIFO and writing a 1 to Bit 3 clears the send FIFO. Writing a 1 to Bit 6 resets the SPI controller.<br/>Bit 7 is set to enable receiving, Bit 8 is set to enable sending. |
|- | |- | ||
|D00C<br/>F8000C | |D00C<br/>F8000C | ||
| | | | ||
|000007F6 | |000007F6 | ||
| − | |Status bits.<br/>Bit 2 is set if data is being sent or received and bits 12-15 are the number of | + | |Status bits.<br/>Bit 0 is set if the receive FIFO is full, and Bit 1 is set if the send FIFO is <i>not</i> full (can accept more writes).<br/>Bit 2 is set if data is being sent or received and bits 12-15 are the number of queued FIFO entries.<br/>Boot code waits for bits 2 and 12-15 to be 0 before/after reading/writing. |
|- | |- | ||
|D010<br/>F80010 | |D010<br/>F80010 | ||
| Line 49: | Line 51: | ||
| | | | ||
| | | | ||
| − | |FIFO in/out. | + | |FIFO in/out. Supports up to a 32-bit data length according to spec, but the eZ80 can only read/write up to 8 bits per FIFO entry. |
|- | |- | ||
|D01C<br/>F8001C | |D01C<br/>F8001C | ||
| Line 64: | Line 66: | ||
|0E0F0F1F | |0E0F0F1F | ||
| | | | ||
| − | |Features (read-only): 32-bit data width, 16- | + | |Features (read-only): 32-bit data width, 16-entry send/receive FIFOs, list of extra protocols supported. |
|} | |} | ||
Revision as of 11:37, 17 March 2022
Synopsis
Port Number: D000
Memory-mapped Address: F80000
Function: LCD Interface
This appears to be an FTSSP010 or compatible SPI controller that interfaces with the LCD. The command set seems to closely match the Sitronix ST7789 family [1].
Note that the SPI controller may also be configured to interface with the ARM coprocessor on Python models, via some ports in the 00xx range. The state of this configuration should be considered unknown when starting a program in TI-OS. In order to reliably use the LCD interface, the _boot_InitializeHardware routine should be called at the start of a program to select the LCD interface and reset its configuration to the default.
| Port | Default | Bits | Information |
| D000 F80000 |
0000F38C | CR0: Boot code writes 180B/09 before/after turning on/off the lcd. | |
| D004 F80004 |
0000182B | 007FFFFF | CR1: Boot code initializes to 02000B. Bits 0-15 are clock divider - 1, bits 16-23 are data length - 1, and bits 24-31 are padding length. Base clock is likely 12 MHz (unconfirmed whether this changes with CPU speed). Sending with a clock divider of 1 seems to be within the LCD controller specs, but receiving may require a larger divider. |
| D008 F80008 |
0002000B | 00000F8F | CR2: Boot code initializes to 010C. Bit 0 is set to transfer data and activate the SPI chip select signal. Writing a 1 to Bit 2 clears the receive FIFO and writing a 1 to Bit 3 clears the send FIFO. Writing a 1 to Bit 6 resets the SPI controller. Bit 7 is set to enable receiving, Bit 8 is set to enable sending. |
| D00C F8000C |
000007F6 | Status bits. Bit 0 is set if the receive FIFO is full, and Bit 1 is set if the send FIFO is not full (can accept more writes). Bit 2 is set if data is being sent or received and bits 12-15 are the number of queued FIFO entries. Boot code waits for bits 2 and 12-15 to be 0 before/after reading/writing. | |
| D010 F80010 |
00002100 | Interrupt control. | |
| D014 F80014 |
00000008 | Interrupt status. | |
| D018 F80018 |
FIFO in/out. Supports up to a 32-bit data length according to spec, but the eZ80 can only read/write up to 8 bits per FIFO entry. | ||
| D01C F8001C |
0E0F0F1F | Inside reserved range. Appears to be a copy of the feature register at D064. | |
| D060 F80060 |
00012100 | Revision (read-only) | |
| D064 F80064 |
0E0F0F1F | Features (read-only): 32-bit data width, 16-entry send/receive FIFOs, list of extra protocols supported. |
Known Commands
| Hex Defaults |
Command | Details |
| 01 | Software Reset | |
| 10 10 |
Enable Sleep Mode | Turns pixels black, low power mode? |
| 11 11 |
Disable Sleep Mode | |
| 12 | Enable Partial Mode | Resets vertical scrolling start to 0. |
| 13 | Disable Partial Mode | Also disables vertical scrolling mode and resets vertical scrolling start to 0. |
| 20 | Uninvert Colors | |
| 21 | Invert Colors | |
| 26 <8:GC> 26 00 26 02 |
Set Gamma | Selects between 4 preset gamma curves: Valid values are 1, 2, 4, 8, invalid values appear to use 1. |
| 28 | Turn Off Display | Turns all pixels white. |
| 29 29 |
Turn On Display | Restore GRAM pixels. |
| 2A <BE16:StartCol> <BE16:EndCol> 2A 0000 013F |
Set Window Columns | Set the pixel update window from StartCol to EndCol inclusive. |
| 2B <BE16:StartLine> <BE16:EndRow> 2B 0000 00EF |
Set Window Rows | Set the pixel update window from StartRow to EndRow inclusive. |
| 30 <BE16:StartRow> <BE16:EndRow> | Set Partial Area Rows | Only displays from StartRow to EndRow inclusive, other lines white. |
| 33 <BE16:TopArea> <BE16:ScrollArea> <BE16:BottomArea> | Vertical Scrolling Definition | TopArea/BottomArea are static (non-scrolling) line counts before and after the ScrollArea whose value is ignored. |
| 36 <8:MAC> 36 08 |
Memory Address Control | Bit 2: Horizontal Refresh Order Bit 3: BGR Order Bit 4: Vertical Refresh Order Bit 5: Column Major Update Bit 6: Column Update Order Bit 7: Row Update Order |
| 37 <BE16:VSP> | Vertical Scrolling Start Position | First line of ScrollArea starts at this GRAM line. |
| 38 | Disable Idle Mode | Restore 18bpp mode. |
| 39 | Enable Idle Mode | 3bpp 8 color mode (only uses msb of each color component). |
| 3A ? 3A 66 |
Interface Pixel Format | Upper and lower nibbles are modes for the two interfaces: 3 is 12bpp, 5 is 16bpp, 6 is 18bpp (msb is ignored, invalid uses 18bpp). |
| B0 ? ? B0 11 F0 |
Interface Control | First Param: Bit 0: Use lcd controller clocks instead of internal clocks. Bit 4: Get GRAM data from lcd controller instead of spi interface. Bit 7: Bypass GRAM and output directly to lcd. Second Param: Polarity of clocks? |
| B1 ? ? ? B1 01 05 14 B1 01 15 14 |
Unknown? | |
| B2 ? ? ? ? ? B2 0C 0C 00 33 33 |
Unknown? | |
| B7 ? B7 35 |
Unknown? | |
| BB ? BB 17 BB 1B |
Unknown? | |
| C0 ? C0 2C C0 22 |
Unknown? | |
| C2 ? C2 01 |
Unknown? | |
| C3 ? C3 03 C3 15 |
Unknown? | |
| C4 ? C4 20 |
Unknown? | |
| C6 ? C6 0F |
Unknown? | |
| D0 ? ? D0 AF A1 |
Unknown? | |
| D2 ? D2 00 |
Unknown? | |
| DC | Unknown? | One parameter "read" and checked if equal to 0x35, but reading doesn't appear to work in the first place... |
| E0 ? ? ? ? ? ? ? ? ? ? ? ? ? ? E0 D0 00 00 10 0F 1A 2D 54 3F 3B 18 17 13 17 E0 D0 00 00 10 0F 1A 2D 54 3F 3B 18 17 13 17 |
Positive Gamma Correction | Definitely affects gamma, parameters unknown and don't match docs. |
| E1 ? ? ? ? ? ? ? ? ? ? ? ? ? ? E1 D0 00 00 10 0F 09 2B 43 40 3B 18 17 13 17 E1 D0 00 00 10 0F 09 2B 43 40 3B 18 17 13 17 |
Negative Gamma Correction | Definitely affects gamma, parameters unknown and don't match docs. |
| E9 ? ? ? E9 08 08 08 |
Unknown? | |
| EB | Something! | |
| F0 | Gamma? | |
| F1 | Gamma? | |
| F2 | Gamma? |
Example
Sending
ld a,036h ; Flips the lcd horizontally, vertically, and swaps the b and r components call spiCmd ld a,0C0h call spiParam ld a,002h ; Resetting the lcd on exit call spiCmd jp boot_InitializeHardware ; Input: A = parameter spiParam: scf ; First bit is set for data .db 030h ; jr nc,? ; skips over one byte ; Input: A = command spiCmd: or a,a ; First bit is clear for commands ld hl,0F80818h call spiWrite ld l,h ld (hl),001h spiWait: ld l,00Dh spiWait1: ld a,(hl) and a,0F0h jr nz,spiWait1 dec l spiWait2: bit 2,(hl) jr nz,spiWait2 ld l,h ld (hl),a ret spiWrite: ld b,3 spiWriteLoop: rla rla rla ld (hl),a ; send 3 bits djnz spiWriteLoop ret
Receiving
This does not appear to work, always returning 0 on the calcs I've tested, due to either a TI bug or hardware issue.
; Input: A = command ; Ouput: A = data spiRead: ld hl,0F80808 ld (hl),00Ch ld l,018h or a,a call spiWrite xor a,a ; not sure what this is for call spiWrite ld l,009h ld (hl),001h dec l ld (hl),081h call spiWait ld l,$18 ld a,(hl) ; dummy read ld a,(hl) ld a,(hl) ; Why is there no wait after dummy read? ld a,(hl) rla rla rla rla rla and a,0E0h ld c,a ld a,(hl) rla rla and a,01Ch or a,c ld c,a ld a,(hl) rra ; why are we throwing away the lsb instead of the msb and a,003h or a,c ret
