Difference between revisions of "Z80 Optimization"

Revision as of 00:35, 26 April 2015

Introduction

Sometimes it is needed some extra speed in ASM or make your game smaller to fit on the calculator. Examples: consuming graphics/data programs and graphics code of mapping, grayscale and 3D graphics.

If you are just looking for cutting some bytes go straight to small tricks in this topic.

Registers and Memory

Generally good algorithms on z80 use registers in a appropriate form. It is also a good practise to keep a convention and plan how you are going to use the registers.

General use of registers:

a - 8-bit accumulator
b - counter
c,d,e,h,l auxiliary to accumulator and copy of b or a

hl - 16-bit accumulator/pointer of a address memory
de - pointer of a destination address memory
bc - 16-bit counter
ix - index register/pointer to table in memory/save copy of hl/pointer to memory when hl and de are being used
iy - index register/pointer to table in memory (use when there is no other option or need optimal execution) (disable interrupts and on exit restore the original value because TI-OS uses)

8-bit vs. 16-bit Operations

The z80 processor makes faster operations on 8-bit values. Code dealing with 16-bit register tends to be bigger and slower because of the equivalent 16-bit instruction is slower or it does not exist and needs to be replaced with more instructions. And sometimes the equivalent 16-bit instruction is 1 more byte. If you use ix or iy registers operations are even slower and always are 1 byte bigger for each instruction. So try to convert your code to use hl and de instead of ix and iy.

In a practical example, imagine: - you pass through the accumulator a value to a routine - if the only valid values of the accumulator range from 0 to 63 and if in that routine you need to multiply the accumulator by, say 12, it has to be stored in a 16-bit pair register. - but you can multiply a by 4 before overflowing (63*4 = 252 which is smaller than 255) and take advantage of this to optimize

Now on the code:

; The most usual way is pass A (the accumulator) right in the start to HL
	ld h,0
	ld l,a
	add a,a
	ld d,h
	ld e,a
	add hl,de
	add hl,hl
	add hl,hl	; hl=a*12
; 9 bytes, 56 clocks

; But given a is between 0 and 63 you can multiply by 4 without overflowing the 8-bit limit (255)
	add a,a
	add a,a		; a*4
	ld l,a
	ld e,a
	ld h,0
	ld d,h		; hl=a*4 and de=a*4
	add hl,hl	; hl=a*8
	add hl,de	; hl=a*12
; 9 bytes, 49 clocks

; hey, minus 7 clock cycles

In this example you only shaved a few clock cycles but sometimes you can save some bytes, too. You can do this for other registers than A accumulator.

For example if passed in l and l is always lower than 64, you can do " sla l \ sla l \ ld h,0 " to multiply l by four and use hl for 16-bit operations. In this case you are exchanging size with speed increase. Each sla instruction is 2 bytes and add hl,hl is only 1 byte.

Mind this optimizations can produce bugs and somewhat hard code to follow, so comment them. I recommend to proceed to this optimization only when you really need speed and the code is bug free.

One common trick with multiplication by 256 is just load around the low byte register to the high byte register. This works because in binary a multiplication by 256 is like shifting 8 bits left, entering zeros. Examples:

; multiply a by 256 and store in hl
	ld h,a
	ld l,0
; multiply hl by 256 and store in ade (pseudo 24-bit pair register)
	ld a,h
	ld d,l
	ld e,0

If you are out of registers, try using ixh/ixl/iyh/iyl and even the i register for loop counters instead of maintaining a counter in memory or pushing/popping an already used register to the stack inside a loop. Using ixh/ixl/iyh/iyl will break compatibility with the TI-84+SE emulated by the Nspire. You can only use i register for other purposes if you disable interrupts first (di).

Shadow registers

In some rare cases, when you run out of registers and cannot to either refactor your algorithm(s) or to rely on RAM storage you may want to use the shadow registers : af', bc', de' and hl'

These registers behave like their "standard" counterparts (af, bc, de, hl) and you can swap the two register sets at using the following instructions :

 ex af, af'  ; swaps af and af' as the mnemonic indicates

 exx         ; swaps bc, de, hl and bc', de', hl'

Shadow registers are somewhat common for doing arithmetic operations on some big integers (16-bit to 32-bit) or BCD operations without rely on RAM storage or pushing and popping to the stack. Example:

MUL32:
        DI
        AND     A               ; RESET CARRY FLAG
        SBC     HL,HL           ; LOWER RESULT = 0
        EXX
        SBC     HL,HL           ; HIGHER RESULT = 0
        LD      A,B             ; MPR IS AC'BC
        LD      B,32            ; INITIALIZE LOOP COUNTER
MUL32LOOP:
        SRA     A               ; RIGHT SHIFT MPR
        RR      C
        EXX
        RR      B
        RR      C               ; LOWEST BIT INTO CARRY
        JR      NC,MUL32NOADD
        ADD     HL,DE           ; RESULT += MPD
        EXX
        ADC     HL,DE
        EXX
MUL32NOADD:
        SLA     E               ; LEFT SHIFT MPD
        RL      D
        EXX
        RL      E
        RL      D
        DJNZ    MUL32LOOP
        EXX
       
; RESULT IN H'L'HL
        RET

Shadow registers can be of a great help but they come with two drawbacks :

they cannot coexist with the "standard" registers : you cannot use ld to assign from a standard to a shadow or vice-versa. Instead you must use nasty constructs such as :

 ; loads hl' with the contents of hl
 push hl
 exx
 pop hl

they require interrupts to be disabled since they are originally intended for use in Interrupt Service Routine. There are situations where it is affordable and others where it isn't. Regardless, it is generally a good policy to restore the previous interrupt status (enabled/disabled) upon return instead of letting it up to the caller. Hopefully it s relatively easy to do (though it does add 4 bytes and 29/33 T-states to the routine) :

  ld a, i  ; this is the core of the trick, it sets P/V to the value of IFF so P/V is set iff interrupts were enabled at that point
  push af  ; save flags
  di       ; disable interrupts
  
  ; do something with shadow registers here

  pop af   ; get back flags
  ret po   ; po = P/V reset so in this case it means interrupts were disabled before the routine was called
  ei       ; re-enable interrupts
  ret

Note that this produces ugly and very hard code to follow, so comment it very well for understanding and debugging later.

SP register

This register is used in desperate situations generally during an interrupt loop demanding as much speed as possible and the normal registers are used. (remarkably used in James Montelongo 4 lvl grayscale interlace in graylib2.inc) You need to know these valid and not generally known instructions:

 ld sp,6
 add hl,sp
 sbc hl,sp
 inc sp
 dec sp

Now an example of such situation:

 ld (saveSP),sp
;init hl,de,bc,a
 ld sp,6
loop:
;code
 add hl,sp  ;get next row of a table for example
;code using bc,de,ix,a
 ld a,b
 or c
 jp nz,loop:
;code
 ld sp,(saveSP)
 ret    ;finish interrupt

When you use sp in this way this means you can not push/pop registers and no calls are allowed. Mind again that this is only used as last resource. Don't forget to save and restore sp like the example shows.

Stack

When you run out of registers, stack may offer an interesting alternative to fixed RAM location for temporary storage.

Allocation

You can either allocate stack space with repeated push, which allows to initialize the data but restricts the allocated space to multiples of 2. An alternate way is to allocate uninitialized stack space (hl may be replaced with an index register) :

 ; allocates 7 bytes of stack space : 5 bytes, 27 T-states instead of 4 bytes, 44 T-states with 4 push which would have forced the alloc of 8 bytes
 ld hl, -7
 add hl, sp
 ld sp, hl

Access

The most common way of accessing data allocated on stack is to use an index register since all allocated "variables" can be accessed without having to use inc/dec but this is obviously not a strict requirement. Beware though, using stack space is not always optimal in terms of speed, depending (among other things) on your register allocation strategy :

 ; 4 bytes, 19 T-states
 ld c, (ix + n)   ; n is an immediate value in -128..127
 
 ; 4 bytes, 17 T-states, destroys a
 ld a, (somelocation)
 ld c, a

If your needs go beyond simple load/store however, this method start to show its real power since it vastly simplify some operations that are complicated to do with fixed storage location (and generally screw up register in the process).

 ; 3 bytes, 19 T-states
 cp (ix + n)

 sub (ix + n)
 sbc a, (ix + n)
 add a, (ix + n)
 adc a, (ix + n)

 inc (ix + n)
 dec (ix + n)

 and (ix + n)
 or (ix + n)
 xor (ix + n)

 ; 4 bytes, 23 T-states
 rl (ix + n)
 rr (ix + n)
 rlc (ix + n)
 rrc (ix + n)
 sla (ix + n)
 sra (ix + n)
 sll (ix + n)
 srl (ix + n)
 bit k, (ix + n)   ; k is an immediate value in 0..7
 set k, (ix + n)
 res k, (ix + n)

Again, choose wisely between hl and an index register depending on the structure of your data the smallest/fastest allocation solution may vary (hl equivalent instructions are generally 2 bytes smaller and 12 T-states faster but do not allow indexing so may require intermediate inc/dec).

Deallocation

If you want need to pop an entry from the stack but need to preserve all registers remember that sp can be incremented/decremented like any 16bit register :

 ; drops the top stack entry : waste 1 byte and 2 T-states but may enable better register allocation...
 inc sp
 inc sp

If you have a large amount of stack space to drop and a spare 16 bit register (hl, index, or de that you can easily swap with hl) :

 ; drop 16 bytes of stack space : 5 bytes, 27 T-states instead of 8 bytes, 80 T-states for 8 pop
 ld hl, 16
 add hl, sp
 ld sp, hl

The larger the space to drop the more T-states you will save, and at some point you'll start saving space as well (beyond 8 bytes)

General Algorithms

Registers and Memory use is very important in writing concise and fast z80 code. Then comes the general optimization.

First, try to optimize the more used code in subroutines and large loops. Finding the bottleneck and solving it, is enough to many programs.

Do not forget that in z80 assembly vector tables (or look up tables) gives smaller and faster code than blocks of comparisons and jumps. Other times using a chunk of data for a task is better than a more usual programming method (notably in graphics screen effects). See Z80 Good Programming Practices for examples.

Look up in a complete instruction set for searching some instruction that can optimize somewhere in the code.

A list of things to keep in mind:

Rework conditionals to be more efficient.
Make sure the most common checks come first. Or said in other way, the more special and rare cases check in last.
Get out of the main loop special cases check if they aren't needed there.
Rearrange program flow
When possible, if you can afford to have a bigger overhead and get code out of the main loop do it.
When your code seems that even with optimization won't be efficient enough, try another approach or algorithm. Search other algorithms in Wikipedia, for instance.
Rewriting code from scratch can bring new ideas (use in desperate situations because of all work needed to write it)
Remember almost all times is better to leave optimization to the end. Optimization can bring too early headaches with crashes and debugging. And because ASM is very fast and sometimes even smaller than higher level languages, it may not be needed further optimization.
Document wacky optimizations to understand the code later (z80 optimization leads to very hard code to understand)

Self Modifying Code

If your code is in ram, writes can be done to change the code. Having a instruction set that explains the opcodes is useful. Despite the self modifying code can be used in any instruction, it is very common with loading constants to registers.

Generally it is used to save any value to be used later (usually seen in masks). Examples:

 ld (savemask),a
;...code...
savemask = $+1
 ld a,$00   ; $00 is just a placeholder

 ld (something),hl
;... code
something = $+1
 ld de,$0000

 ld (saveSP),sp
;... code ...
saveSP = $+1
 ld sp,$0000  ; restore sp

SMC (Self Modifying Code) is quite used with unrolling and relative jumps. Example:

 ld (jpmodify),a
;...
jpmodify = $+1
 jr $00
 rrca
 rrca
 rrca
 rrca
 rrca
 rrca
 rrca
 rrca

Another SMC is modifying load instructions with (ix+0) and change the 0 to other values to really quickly read and write to the nth element of a list without using any extra registers.

Small Tricks

Note that the following tricks act much like a peep-hole optimizer and are the last optimization step : remember to first optimize your algorithm and register allocation before applying any of the following if you really want the fastest speed and the smallest code.

Also note that near every trick turn the code less understandable and documenting them is a good idea. You can easily forgot after a while without reading parts of the code.

Be warned that some tricks are not exactly equivalent to the normal way and may have exceptions on its use, comments warn about them. Some tricks apply to other cases, but again you have to be careful.

There are some tricks that are nothing more than the correct use of the available instructions on the z80. Keeping an instruction set summary, help to visualize what you can do during coding.

Optimize size and speed

Loading stuff

;Instead of:
 ld a,0
;Try this:
 xor a    ;disadvantages: changes flags
;or
 sub a    ;disadvantages: changes flags
; -> save 1 byte and 3 T-states

;Instead of
	ld b,$20
	ld c,$30
;try this
	ld bc,$2030
;or this
	ld bc,(b_num * 256) + c_num		;where b_num goes to b register and c_num to c register
; -> save 1 byte and 4 T-states

;Instead of
  ld a,$42
  ld (hl),a
;try this
  ld (hl),$42
; -> save 1 byte and 4 T-states

;Instead of
	xor a
	ld (data1),a
	ld (data2),a
	ld (data3),a
	ld (data4),a
	ld (data5),a	;if data1 to data5 are one after the other
;try this
	ld hl,data1
	ld de,data1+1
	xor a
	ld (hl),a
	ld bc,4
	ldir
; -> save 3 bytes for every ld (dataX), after passing the initial overhead

;Instead of
	ld a,(var)
	inc a
	ld (var),a
;try this	;Note: if hl is not tied up, use indirection:
	ld hl,var
	inc (hl)
	ld a,(hl) ;if you don't need (hl) in a, delete this line
; -> save 2 bytes and 2 T-states

; Instead of :
 ld a, (hl)
 ld (de), a
 inc hl
 inc de
; Use :
 ldi
 inc bc
; -> save 1 byte and 4 T-states

;Never use:
    push BC
;    ...
    pop BC
    ld D,B
    ld E,C
;Use instead:
    push BC
;    ...
    pop DE      ;we only want to DE hold pushed BC (no need for a copy of DE in BC)
; -> save 2 bytes and 8 T-states

Math and Logic tricks

;Instead of:
 cp 0
;Use
 or a
; -> save 1 byte and 3 T-states

  cp 1
; >
  dec a   ;changes a!
; -> save 1 byte and 3 T-states

  xor %11111111
; >
  cpl
; -> save 1 byte and 3 T-states

;Instead of
    ld de,767
    or a       ;reset carry so sbc works as a sub
    sbc hl,de
;try this
    ld de,-767 ;negation of de
    add hl,de
; -> 2 bytes and 8 T-states !

;Instead of
    ld de,-767
    add hl,de
;try this
    dec h  ; -256
    dec h  ; -512
    dec h  ; -768
    inc hl  ; -767
;Note that works in many other cases
; -> save 3 T-states

;Instead of
	srl a
	srl a
	srl a
;try this
	rrca
	rrca
	rrca
	and %00011111
; -> save 1 byte and 5 T-states

;Instead of
	neg
	add a,N   ;you want to calculate N-A
;Do it this way:
	cpl
	add a,N+1    ;neg is practically equivalent to cpl \ inc a
; -> save 1 byte and 4 T-states

;Never use:
    ld A,B
    neg
;Instead use:
    xor A
    sub B
; -> save 1 byte and 4 T-states

;Never use:
    ld A,D
    sub $D3
    neg
;Instead use:
    ld A,$D3
    sub D
; -> save 2 bytes and 8 T-states

  sla l
  rl h         ; I've actually seen this!
; >
  add hl,hl
; -> save 3 bytes and 5 T-states

Conditionals

  and 1
  cp 1
  jr z,foo
; >
  and 1         ;and sets zero flag, no need for cp
  jr nz,foo
; -> save 2 bytes and 7 T-states

  and 1
  cp 1         ;a not needed after this
  jr z,foo
; >
  rra
  jr c,foo

  bit 0,a
  call z,foo
; >
  rra
  call nc,foo

  bit 7,a
  jr z,foo
; >
  rla
  jr nc,foo

  bit 2,a
  ret nz
  xor a
; >
  and %100
  ret nz

  cp 9        ;if a>=9 then goto label
  jp nc,label
  jp z,label
; >
  cp 9+1      ;;if a>10 then goto label
  jp nc,label
; -> save 3 bytes and 10 T-states

Code Flow

Almost never call and return...

;Instead of
 call xxxx
 ret
;try this
 jp xxxx
;only do this if the pushed pc to stack is not passed to the call. Example: some kind of inline vputs.
; -> save 1 byte and 17 T-states

;Never use:
    dec B
    jr NZ,loop    ;I have seen this...
;Use:
    djnz loop
; save 1 byte and 3 T-states

; Instead of
 ld a,(Number)
 cp 0
 jp z,A_is_0
 cp 1
 jp z,A_is_1
 cp 2
 jp z,A_is_2
 cp 3
 jp z,A_is_3
 cp 4
 jp z,A_is_4
 cp 5
 jp z,A_is_5

; This is a little better
 ld a,(Number)
 or a
 jp z,A_is_0
 dec a
 jp z,A_is_1
 dec a
 jp z,A_is_2
 sub 2
 jp z,A_is_4
 dec a
 jp z,A_is_5

; Even better
 ld a,(Number)
 add a,a   ; a*2 (limits Number to 128) 
 ld h,0 
 ld l,a 
 ld de,VectorTable
 add hl,de
 ld a,(hl)
 inc hl
 ld h,(hl)
 ld l,a
 jp (hl)

VectorTable:
 .dw A_is_1
 .dw A_is_2
 .dw A_is_3
 .dw A_is_4
 .dw A_is_5
 .dw A_is_6

Also see Z80 Good Programming Practices

Fallthrough looping If you need to repeat a routine several times but can't spare registers for a loop counter or unroll the routine, try structuring the routine so it can call itself several times and fall through at the end. For example:

foo:
  ld hl, data
  call bar      ; Run routine once
  call bar      ; .. twice
  call bar      ; .. three times
bar:
  ld a, (hl)    ; .. fourth and final time
  inc l
  and $0F
  out (c), a
  ret

Others

Toggling values in loops.

;Instead of
loop:
 ld a,2
;code1
 ld a,0
;code2
 djnz loop

;try this
 ld a,2
loop:
;code1
 xor $01   ; the trick is xor logic make a register alternate between two values
;code2
 djnz loop
; -> save size and time depending on its use

Table alignment

If you align tables to a 256-byte boundary, you can access the contents by placing the index in a register such as l and the table address in h. This is faster than loading the full unaligned 16-bit address and adding a 16-bit index to it, and makes accessing tables with a size of 256 bytes or less very convenient:

 ld h, (sineTable >> 8) & $FF    ; Get MSB of table
 ld a, (frame_count)             ; Get index
 ld l, a
 ld a, (hl)                      ; Look up value

Instead of:

 ld hl, sineTable                ; Get address of table
 xor a
 ld d, a                         ; Set index high byte to zero
 ld a, (frame_count)
 ld e, a                         ; Set index low byte
 add hl, de                      ; Add offset to base
 ld a, (hl)                      ; Look up value

Size vs. Speed

The classical problem of optimization in computer programming, Z80 is no exception. In ASM most frequently size is what matters because generally ASM is fast enough and it is nice to give a user a smaller program that doesn't use up most RAM memory.

For the sake of size

Use relative jumps (jr label) whenever possible. When relative jump is out of reach (out of -128 to 127 bytes) and there is a jp near, do a relative jump to the absolute one. Example:

;lots of code (more that 128 bytes worth of code)
somelabel2:
 jp somelabel
;less than 128 bytes
 jr somelabel2   ;instead of a absolute jump directly to somelabel, jump to a jump to somelabel.

Relative jumps are 2 bytes and absolute jumps 3. In terms of speed jp is faster when a jump occurs (10 T-states) and jr is faster when it doesn't occur.

;Instead of
 dec bc
 ld a,b
 or c
 ret z
;try this
 cpi              ;increments HL
 ret po
; save 1 byte at the cost of 2 T-states

Passing inline data

When you call, the pc + 3 (after the call) is pushed. You can pop it and use as a pointer to data. A very nifty use is with strings. To return, pass the data and jp (hl).

Instead of:
 ld hl,string
 bcall(_vputs)
 ret
;Try this:
  call Disp
  .db "This is some text",0
  ret
;Not a speed optimization, but it eliminates 2-byte pointers, since it just uses the call's return address.
;It also heavily disturbs disassembly.
Disp:
  pop hl
  bcall(_vputs)
  jp (hl)
; -> save 2 bytes for each use, but 4 bytes of overhead (Disp routine)

This routine can be expanded to pass the coordinates where the text should appear.

Wasting time to delay

There are those funny times that you need some delay between operations like reads/writes to ports and there is nothing useful to do. And because nop's are not very size friendly, think of other slower but smaller instructions. Example:

;Instead of
 ld a,KEY_GROUP
 out (1),a
 nop
 nop
 in a,(1)
;Try this:
 ld a,KEY_GROUP
 out (1),a
 ld a,(de)    ;a doesn't need to be preserved because it will hold what the port has.
 in a,(1)
; -> save 1 byte and 1 T-state (well 1 T-state less is almost the same time)

When you need to delay and cannot afford to alter registers or flags there are still ways to delay that waste less size than nop's :

; 2 bytes, 8 T-states
 nop
 nop

; 2 bytes, 12 T-states
 inc hl
 dec hl

; 2 bytes, 12 T-states
 jr $+2

; 2 bytes, 21 T-states
 push af
 pop af

; 2 bytes, 38 T-states
 ex (sp), hl
 ex (sp), hl

If you need a small adjustable delay:

;4 bytes, b*13+8 T-states (variable)
	ld b,255	; initial delay
	djnz $		; do it
;b=0 on exit

Notes:

There are many other instructions that you can use
Beware that not all instructions preserve registers or flags
For delay between frames of games or other longer delays, you can use the 'halt' instruction if there are interrupts enabled. It make the calculator enter low power mode until an interrupt is triggered. To fine-tune the effect of this delay mechanism you can alter interrupt mask and interrupt time speed beforehand (and possibly restore their values afterwards).

Unrolling code

General Unrolling You can unroll some loop several times instead of looping, this is used frequently on math routines of multiplication. This means you are wasting memory to gain speed. Most times you are preferring size to speed.

Unroll commands

; "Classic" way : ~21 T-states per byte copied
 ld hl,src
 ld de,dest
 ld bc,size
 ldir

; Unrolled : (16 * size + 10) / n -> ~18 T-states per byte copied when unrolling 8 times
 ld hl,src
 ld de,dest
 ld bc,size  ; if the size is not a multiple of the number of unrolled ldi then a small trick must be used to jump appropriately inside the loop for the first iteration
loopldi:    ;you can use this entry for a call
 ldi
 ldi
 ldi
 ldi
 ldi
 ldi
 ldi
 ldi
 jp pe, loopldi    ; jp used as it is faster and in the case of a loop unrolling we assume speed matters more than size
; ret if this is a subroutine and use the unrolled ldi's with a call.

This unroll of ldi also works with outi and ldr.

Looping with 16 bit counter

There are two ways to make loops with a 16bit counter :

the naive one, which results in smaller code but increased loop overhead (24 * n T-states) and destroys a

  ld bc, ...
loop:
  ; loop body here
 
  dec bc
  ld  a, b
  or  c
  jp  nz,loop

the slightly trickier one, which takes a couple more bytes but has a much lower overhead (12 * n + 14 * (n / 16) T-states)

  dec  de
  ld  b, e
  inc  b
  inc  d
loop2:
  ; loop body here
  
  djnz loop2
  dec  d
  jp  nz,loop2

The rationale behind the second method is to reduce the overhead of the "inner" loop as much as possible and to use the fact that when b gets down to zero it will be treated as 256 by djnz.

You can therefore use the following macros for setting proper values of 8bit loop counters given a 16bit counter in case you want to do the conversion at compile time :

  #define inner_counter8(counter16) (((counter16) - 1) & 0xff) + 1
  #define outer_counter8(counter16) (((counter16) - 1) >> 8) + 1

Preserve Registers

; description: both routines compare b to 0, same size and speed but the second preserves accumulator
; remarks: - inc/dec doesn't affect carry flag
;          - inc/dec doesn't affect any flags on 16-bit registers, so do not extrapolate to 16-bit registers.
	ld a,b
	or b
	jr z,label
; >
	inc b
	dec b
	jr z,label

; description: add a to hl without using a 16-bit register
;normal way:
	ld d,$00
	ld e,a
	add hl,de
;4 bytes and 22 clock cycles
; >
	add a,l
	ld l,a
	jr nc, $+3
	inc h
;5 bytes, 19/20 clock cycles

Setting flags

In some occasion you might want to selectively set/reset a flag.

Here are the most common uses :

; set Carry flag
 scf

; reset Carry flag (alters Sign and Zero flags as defined)
 or a

; alternate reset Carry flag (alters Sign and Zero flags as defined)
 and a

; set Zero flag (resets Carry flag, alters Sign flag as defined)
 cp a

; reset Zero flag (alters a, reset Carry flag, alters Sign flag as defined)
 or 1

; set Sign flag (negative) (alters a, reset Zero and Carry flags)
 or $80

; reset Sign flag (positive) (set a to zero, set Zero flag, reset Carry flag)
 xor a

Other possible uses (much rarer) :

;Set parity/overflow (even):
 xor a

;Reset parity/overflow (odd):
 sub a

;Set half carry (hardly ever useful but still...)
 and a

;Reset half carry (hardly ever useful but still...)
 or a

;Set bit 5 of f:
 or %00100000

As you can see these are extremely simple, small and fast ways to alter flags which make them interesting as output of routines to indicate error/success or other status bits that do not require a full register.

Were you to use this, remember that these flag (re)setting tricks frequently overlap so if you need a special combination of flags it might require slightly more elaborate tricks. As a rule of a thumb, always alter the carry last in such cases because the scf and ccf instructions do not have side effects.

More advance ways of manipulating flags follow:

;get the zero flag in carry 
	scf
	jr z,$+3
	ccf

;Put carry flag into zero flag.
	ccf
	sbc a, a

Tools of the job

Want to try test your optimization or test new ones? Then you have to check this:

Keep a z80 instruction set to not forget a useful instruction and flags affected. (see Z80_Instruction_Set)
Use an assembler that has ".echo" directive and use this in the source to count size: (see Assemblers)

SomeCodeorData:
;code or data goes here
End:
 .echo "size of the code/data:"
 .echo End-SomeCodeorData

Get a nice IDE of z80 that counts code (IDE's)
Make use of the counting capabilities of an emulator (Emulators) (see wabbitemu)

Very specific optimizations (hardly practical)

Table alignment

Use an aligned address on memory such as $8000 (theoretical example) and if you will only use 256 bytes ($8000 to $80FF), to get the next byte use inc l instead of inc hl.

Crazy, "magick", hacks and obscure optimization's tricks

These are not normally recommend for use because some disturb disassembly and even coders understanding the code.

Better else

So you normally have an if-else-endif block like this:

jr nz,else    ;the IF
;some code
jr endif
else:
;some code
endif:

But here's a crazy trick for when the Else code is a single 2-byte instruction: You use the first byte of a 3 byte instruction with no side effects instead of the "jr endif" line! So if you had code like this:

cp 7
jr nz,else
ld a,3
jr endif
else:
ld a,4
endif:

You could replace it with this:

cp 7
jr nz,else
ld a,3
.db $C2  ;jp nz,xxxx
else:
ld a,4
endif:

Instead of branching over the ld a,4 instruction, it now executes a jp nz,XXXX instruction where the XXXX is the two bytes of the next instruction. You already know what the flags will be here, so you can make the jump never taken. You can use this to skip the next two bytes of execution! Who needs to branch over it?

This only takes 28 T-states for if. A small saving, but could be useful in tight loops, and saves 2 bytes! The only reason not to use this for 1-byte instructions would be code readability and bug safety. Watch those flags!

Conditional rst

For a smaller conditional rst $38, use jr cc, -1. This will cause a conditional jump to the displacement byte ($FF) which is the rst $38 opcode.

DAA trick

Normally DAA instruction is used for BCD math but can be used for converting (?) ASCII integer.

	cp 10
	ccf
	adc a, 30h
	daa

Acknowledgements

fullmetalcoder
Galandros
Dwedit for sharing in MaxCoderz the "Better else"
MaxCoderz participants in assembly optimizing topic (Jim e,CoBB,...)
SMS Power wiki

@@ Line 164: / Line 164: @@
   </nowiki>
-Now a example of such situation:
+Now an example of such situation:
   <nowiki>
   ld (saveSP),sp

Difference between revisions of "Z80 Optimization"

Revision as of 00:35, 26 April 2015

Contents

Introduction

Registers and Memory

8-bit vs. 16-bit Operations

Shadow registers

SP register

Stack

Allocation

Access

Deallocation

General Algorithms

Self Modifying Code

Small Tricks

Optimize size and speed

Loading stuff

Math and Logic tricks

Conditionals

Code Flow

Others

Size vs. Speed

For the sake of size

Unrolling code

Looping with 16 bit counter

Preserve Registers

Setting flags

Tools of the job

Very specific optimizations (hardly practical)

Table alignment

Crazy, "magick", hacks and obscure optimization's tricks

Better else

Conditional rst

DAA trick

Related topics

Acknowledgements

Navigation menu

Search